oh christmas tree, oh christmas tree

Look what we found over at mollie makes. I think every house needs one of these or even one for your desk at work?

Check it out:

Even the smallest of dwellings requires a Christmas tree. This one is made from pretty Japanese papers in green, silver and gold and is very straightforward to make based on a simple folded fan shape. You could just as easily make yours from giftwrap, or go for an all white look for sophisticated elegance.

Paper fold Christmas tree as seen in Mollie Makes Christmas.

Materials:

14 paper rectangles, two of each measuring 21 x 28cm (81⁄4 x 11in), 18 x 28cm (7 x 11in), 16 x 28cm (61⁄4 x 11in), 13.5 x 26cm (51⁄4 x 101⁄8in), 12 x 26cm (43⁄4 x 101⁄8in),
9 x 25cm (31⁄2 x 97⁄8in), 6 x 22cm (23⁄8 x 85⁄8in)

Piece of patterned paper measuring

11.5 x 11.5cm (41⁄2 x 41⁄2in) for the trunk

One sheet of A4 (US letter) silver paper for the base

Two 30cm (12in) wooden barbeque skewers

Thin wire

Pencil and ruler

Craft knife and cutting mat

Small pair of scissors

Glue stick and quick-drying glue tube

Darning needle

 

Method:

Make the base of the tree.

01
Start by making the base for the tree. Cut strips of paper 2cm (¾in) wide. Take the first strip, run a glue stick along one side and start winding it up into a tight coil. As you come to the end of one strip, glue on another strip and continue winding, until you have a disc at least 3.5cm (1³⁄8in) wide. The wider the base the more stable the tree will be; to ensure your tree stands straight, make the base as flat as possible.

02
Taking one of the larger paper rectangles, place it pattern side down with one of the short edges facing you and fold over by 1.5cm (5⁄8in). Turn the paper over and fold the other way, again by 1.5cm (5⁄8in). Continue to concertina fold in this way to the end of the strip (if you are left with a spare bit that is not big enough to fold, trim it off).

 

Concertina fold and trim

03
Trim the ends of the folded strip to a point, curving the cut slightly to give a scalloped point.

 

Glue to make a semi-circle.

04
Fold the pleated strip in half and press firmly at the crease. Run a glue stick along one edge of the fan shape and stick to the other edge to make a semi-circle.

 

Stick two semi circles together.

05
Fold the correspondingly-sized paper rectangle in the same way, then stick the two semi-circles together to form a complete circle.

 

Make six other branch layers.

06
Take a small piece of wire approx 14cm (5½in) long. Fold it in half and poke the ends through at the centre of the circle from front to back on either side of the two joined semi-circles. Turn over and twist the ends of the wire together to secure. This completes a branch layer.Repeat steps 2–6 to make the other six branch layers from the pairs of paper rectangles.

07
Take the patterned paper square (for the trunk) and run the glue stick over the reverse side leaving a 2cm (¾in) strip unglued along one edge. Starting at the unglued edge, roll up to make a tube approx 1.5cm (5⁄8in) in diameter. Cut into sections as follows: one measuring 2.5cm (1in), three measuring 2cm (¾in) and two measuring 1.5cm (5⁄8in).

 

Thread the paper branch circles onto skewers.

08
Starting with the second smallest circle, begin to thread the paper fold circles onto the skewers, placing the skewer ends through the holes where the wire joins the two semi-circles. Setting aside the two smallest paper tubes, use the paper tubes in ascending size to separate the paper fold circles. Push the circles/tubes along the length of the skewers to approx 1.5cm (5⁄8in) from the top.

Secure the tree to the base.

09
Once the largest circle has been threaded on, it is time to secure the tree to the base. Prepare the base by using the darning needle to pierce two holes approx 1cm (³⁄8in) apart either side of the centre. Thread on one of the set-aside small paper tubes, place a blob of quick-drying glue into each hole, and push the skewers right down into the holes.

10
Thread the other small paper tube onto the skewers at the top of the tree, place a blob of quick-drying glue onto the end of each skewer and stick the smallest paper fold circle on to finish.

Tip

The pleated circles also make wonderful decorations. Fold some really large ones in gold and silver and hang them up for a stunning display.

happy christmas crafting

handsome and pretty

x

Advertisements

Let your voice be heard

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s